SPEC CPU®2017 Floating Point Speed Result

Copyright 2017-2019 Standard Performance Evaluation Corporation

Hewlett Packard Enterprise (Test Sponsor: HPE)

ProLiant DL325 Gen10
(2.00 GHz, AMD EPYC 7702P)

SPECspeed®2017_fp_base = 12600

SPECspeed®2017_fp_energy_base = 38700

SPECspeed®2017_fp_peak = 12600

SPECspeed®2017_fp_energy_peak = 38800
CPU2017 License: 003 Test Date: Aug-2019
Test Sponsor: HPE Hardware Availability: Oct-2019
Tested by: HPE Software Availability: Aug-2019

Benchmark result graphs are available in the PDF report.

Hardware
CPU Name: AMD EPYC 7702P
  Max MHz: 3350
  Nominal: 2000
Enabled: 64 cores, 1 chip
Orderable: 1 chip
Cache L1: 32 KB I + 32 KB D on chip per core
  L2: 512 KB I+D on chip per core
  L3: 256 MB I+D on chip per chip,
16 MB shared / 4 cores
  Other: None
Memory: 256 GB (8 x 32 GB 2Rx4 PC4-2933Y-L)
Storage: 1 x HPE 480 GB SATA 6G SSD
Other: None
Software
OS: SUSE Linux Enterprise Server 15 (x86_64) SP1
Kernel 4.12.14-195-default
Compiler: C/C++/Fortran: Version 2.0.0 of AOCC
Parallel: Yes
Firmware: HPE BIOS Version A41 07/20/2019 released Aug-2019
File System: btrfs
System State: Run level 3 (multi-user)
Base Pointers: 64-bit
Peak Pointers: 64-bit
Other: jemalloc: jemalloc memory allocator library v5.2.0
Power Management: Disabled
Power
Max. Power (W): 400.27
Idle Power (W): 191.07
Min. Temperature (C): 20.75
Elevation (m): 132
Line Standard: 208 V / 60 Hz / 1 phase / 2 wires
Provisioning: Line-powered
Power Settings
Management FW: Version 1.43 of iLO5 released May 23 2019
Memory Mode: Normal
Power-Relevant Hardware
Power Supply: 1 x 800 W (non-redundant)
  Details: HPE 800W Flex Slot Titanium Hot Plug Low Halogen
Power Supply Kit (865438-B21)
Backplane: 8 SFF NVMe with optional optical drive
Other Storage: Embedded SATA Controller
Storage Model #s: P05976-B21
NICs Installed: 1 x HPE Ethernet 4-port 331i Adapter @ 1 Gb
NICs Enabled (FW/OS): 4 / 4
NICs Connected/Speed: 2 @ 1 Gb
Other HW Model #s: 7 x High Performance fans
Power Analyzer
Power Analyzer: 10.216.1.15:8888
Hardware Vendor: Yokogawa
Model: YokogawaWT210
Serial Number: 91K308562
Input Connection: GPIB via NI GIPB-USB-HS
Metrology Institute: NIST
Calibration By: TRANSCAT
Calibration Label: 5-E553M-20-1
Calibration Date: 21-May-2019
PTDaemon™ Version: 1.9.1 (a2d19f26; 2019-07-17)
Setup Description: SUT Power Supply 1 via neoXt NXB 20815
Current Ranges Used: 1A, 2A
Voltage Range Used: 300V
Temperature Meter
Temperature Meter: 10.216.1.15:8889
Hardware Vendor: Digi International Inc.
Model: DigiWATCHPORT_H
Serial Number: V45297862
Input Connection: USB
PTDaemon Version: 1.9.1 (a2d19f26; 2019-07-17)
Setup Description: 5 mm in front of SUT main intake

Base Results Table

Benchmark Threads Seconds Ratio Energy
(kJ)		 Energy
Ratio		 Average
Power		 Maximum
Power		 Seconds Ratio Energy
(kJ)		 Energy
Ratio		 Average
Power		 Maximum
Power		 Seconds Ratio Energy
(kJ)		 Energy
Ratio		 Average
Power		 Maximum
Power
SPECspeed®2017_fp_base 12600
SPECspeed®2017_fp_energy_base 38700
Results appear in the order in which they were run. Bold underlined text indicates a median measurement.
603.bwaves_s 64 1670 3540 65.4 9850 392 399 1670 3540 65.6 9810 394 399 1670 3540 65.5 9820 393 399
607.cactuBSSN_s 64 81.0 2060 29.2 6240 361 376 81.8 2040 29.5 6180 361 376 80.8 2060 29.1 6270 360 376
619.lbm_s 64 1630 32.2 61.3 97.1 377 383 1620 32.3 61.4 97.0 378 384 1630 32.2 61.6 96.6 378 384
621.wrf_s 64 1000 1320 34.9 4130 348 359 1000 1320 34.9 4130 349 359 99.4 1330 34.8 4150 350 359
627.cam4_s 64 1030 86.0 37.3 2580 362 394 1030 85.9 37.4 2580 362 393 1030 85.9 37.5 2570 363 394
628.pop2_s 64 1810 65.6 62.1 2100 343 355 1820 65.4 62.2 2100 342 355 1800 65.8 62.0 2110 344 357
638.imagick_s 64 72.4 1990 22.6 6940 313 358 71.5 2020 22.4 7030 313 351 72.5 1990 22.8 6900 314 350
644.nab_s 64 58.0 3010 19.9 9550 343 356 58.3 3000 19.9 9530 342 356 58.1 3010 20.0 9500 344 356
649.fotonik3d_s 64 1490 61.4 52.6 1940 354 381 1490 61.3 52.6 1950 353 380 1500 60.7 52.9 1930 353 380
654.roms_s 64 1010 1560 39.7 4430 393 399 1010 1550 39.7 4440 391 398 1010 1560 39.7 4430 392 398

Peak Results Table

Benchmark Threads Seconds Ratio Energy
(kJ)		 Energy
Ratio		 Average
Power		 Maximum
Power		 Seconds Ratio Energy
(kJ)		 Energy
Ratio		 Average
Power		 Maximum
Power		 Seconds Ratio Energy
(kJ)		 Energy
Ratio		 Average
Power		 Maximum
Power
SPECspeed®2017_fp_peak 12600
SPECspeed®2017_fp_energy_peak 38800
Results appear in the order in which they were run. Bold underlined text indicates a median measurement.
603.bwaves_s 64 1670 3540 65.4 9850 392 399 1670 3540 65.6 9810 394 399 1670 3540 65.5 9820 393 399
607.cactuBSSN_s 64 80.4 2070 29.1 6260 362 377 81.7 2040 29.5 6180 361 376 80.5 2070 29.0 6280 361 376
619.lbm_s 64 1630 32.2 61.3 97.1 377 383 1620 32.3 61.4 97.0 378 384 1630 32.2 61.6 96.6 378 384
621.wrf_s 64 99.8 1320 34.8 4150 349 358 99.2 1330 34.6 4170 349 358 99.5 1330 34.8 4160 349 359
627.cam4_s 64 1030 86.0 37.3 2580 362 394 1030 85.9 37.4 2580 362 393 1030 85.9 37.5 2570 363 394
628.pop2_s 64 1810 65.6 62.1 2100 343 355 1820 65.4 62.2 2100 342 355 1800 65.8 62.0 2110 344 357
638.imagick_s 64 72.4 1990 22.6 6940 313 358 71.5 2020 22.4 7030 313 351 72.5 1990 22.8 6900 314 350
644.nab_s 64 58.0 3010 19.9 9550 343 356 58.3 3000 19.9 9530 342 356 58.1 3010 20.0 9500 344 356
649.fotonik3d_s 64 1490 61.4 52.6 1940 354 381 1490 61.3 52.6 1950 353 380 1500 60.7 52.9 1930 353 380
654.roms_s 64 1010 1560 39.7 4430 393 399 1010 1560 39.5 4460 392 399 1010 1560 39.8 4430 393 399

Compiler Notes

The AMD64 AOCC Compiler Suite is available at
http://developer.amd.com/amd-aocc/

Submit Notes

The config file option 'submit' was used.
'numactl' was used to bind copies to the cores.
See the configuration file for details.

Operating System Notes

'ulimit -s unlimited' was used to set environment stack size
'ulimit -l 2097152' was used to set environment locked pages in memory limit

runcpu command invoked through numactl i.e.:
numactl --interleave=all runcpu <etc>

Set dirty_ratio=8 to limit dirty cache to 8% of memory
Set swappiness=1 to swap only if necessary
Set zone_reclaim_mode=1 to free local node memory and avoid remote memory
sync then drop_caches=3 to reset caches before invoking runcpu

dirty_ratio, swappiness, zone_reclaim_mode and drop_caches were
all set using privileged echo (e.g. echo 1 > /proc/sys/vm/swappiness).

Transparent huge pages set to 'always' for this run (OS default)

Environment Variables Notes

Environment variables set by runcpu before the start of the run:
GOMP_CPU_AFFINITY = "0-63"
LD_LIBRARY_PATH =
     "/cpu2017/amd_speed_aocc200_rome_C_lib/64;/cpu2017/amd_speed_aocc200_rom
     e_C_lib/32:"
MALLOC_CONF = "retain:true"
OMP_DYNAMIC = "false"
OMP_SCHEDULE = "static"
OMP_STACKSIZE = "128M"
OMP_THREAD_LIMIT = "64"

Environment variables set by runcpu during the 607.cactuBSSN_s peak run:
GOMP_CPU_AFFINITY = "0-63"

Environment variables set by runcpu during the 621.wrf_s peak run:
GOMP_CPU_AFFINITY = "0-63"

Environment variables set by runcpu during the 654.roms_s peak run:
GOMP_CPU_AFFINITY = "0-63"

General Notes

Binaries were compiled on a system with 2x AMD EPYC 7601 CPU + 512GB Memory using Fedora 26

NA: The test sponsor attests, as of date of publication, that CVE-2017-5754 (Meltdown)
is mitigated in the system as tested and documented.
Yes: The test sponsor attests, as of date of publication, that CVE-2017-5753 (Spectre variant 1)
is mitigated in the system as tested and documented.
Yes: The test sponsor attests, as of date of publication, that CVE-2017-5715 (Spectre variant 2)
is mitigated in the system as tested and documented.

jemalloc: configured and built with GCC v9.1.0 in Ubuntu 19.04 with -O3 -znver2 -flto
jemalloc 5.1.0 is available here:
https://github.com/jemalloc/jemalloc/releases/download/5.1.0/jemalloc-5.1.0.tar.bz2


Submitted_by: "Bucek, James" <[email protected]>
Submitted: Tue Sep 17 00:02:18 EDT 2019
Submission: cpu2017-20190903-17798.sub

Submitted_by: "Bucek, James" <[email protected]>
Submitted: Tue Sep 17 09:00:11 EDT 2019
Submission: cpu2017-20190903-17798.sub

Platform Notes

BIOS Configuration:
 AMD SMT Option set to Disabled
 Thermal Configuration set to Maximum Cooling
 Determinism Control set to Manual
 Performance Determinism set to Power Deterministic
 Memory Patrol Scrubbing set to Disabled
 NUMA memory domains per socket set to Four memory domains per socket
 Workload Profile set to General Peak Frequency Compute
 Minimum Processor Idle Power Core C-State set to C6 State

 Sysinfo program /cpu2017/bin/sysinfo
 Rev: r6365 of 2019-08-21 295195f888a3d7edb1e6e46a485a0011
 running on dl325gen10 Sat Aug 31 19:41:38 2019

 SUT (System Under Test) info as seen by some common utilities.
 For more information on this section, see
    https://www.spec.org/cpu2017/Docs/config.html#sysinfo

 From /proc/cpuinfo
    model name : AMD EPYC 7702P 64-Core Processor
       1  "physical id"s (chips)
       64 "processors"
    cores, siblings (Caution: counting these is hw and system dependent. The following
    excerpts from /proc/cpuinfo might not be reliable.  Use with caution.)
       cpu cores : 64
       siblings  : 64
       physical 0: cores 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
       25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52
       53 54 55 56 57 58 59 60 61 62 63

 From lscpu:
      Architecture:        x86_64
      CPU op-mode(s):      32-bit, 64-bit
      Byte Order:          Little Endian
      Address sizes:       48 bits physical, 48 bits virtual
      CPU(s):              64
      On-line CPU(s) list: 0-63
      Thread(s) per core:  1
      Core(s) per socket:  64
      Socket(s):           1
      NUMA node(s):        4
      Vendor ID:           AuthenticAMD
      CPU family:          23
      Model:               49
      Model name:          AMD EPYC 7702P 64-Core Processor
      Stepping:            0
      CPU MHz:             2000.000
      CPU max MHz:         2000.0000
      CPU min MHz:         1500.0000
      BogoMIPS:            3992.33
      Virtualization:      AMD-V
      L1d cache:           32K
      L1i cache:           32K
      L2 cache:            512K
      L3 cache:            16384K
      NUMA node0 CPU(s):   0-15
      NUMA node1 CPU(s):   16-31
      NUMA node2 CPU(s):   32-47
      NUMA node3 CPU(s):   48-63
      Flags:               fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov
      pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt pdpe1gb rdtscp lm
      constant_tsc rep_good nopl xtopology nonstop_tsc cpuid extd_apicid aperfmperf pni
      pclmulqdq monitor ssse3 fma cx16 sse4_1 sse4_2 movbe popcnt aes xsave avx f16c
      rdrand lahf_lm cmp_legacy svm extapic cr8_legacy abm sse4a misalignsse 3dnowprefetch
      osvw ibs skinit wdt tce topoext perfctr_core perfctr_nb bpext perfctr_l2 mwaitx cpb
      cat_l3 cdp_l3 hw_pstate ssbd ibrs ibpb stibp vmmcall fsgsbase bmi1 avx2 smep bmi2
      cqm rdt_a rdseed adx smap clflushopt clwb sha_ni xsaveopt xsavec xgetbv1 xsaves
      cqm_llc cqm_occup_llc cqm_mbm_total cqm_mbm_local clzero irperf xsaveerptr arat npt
      lbrv svm_lock nrip_save tsc_scale vmcb_clean flushbyasid decodeassists pausefilter
      pfthreshold avic v_vmsave_vmload vgif umip rdpid overflow_recov succor smca

 /proc/cpuinfo cache data
    cache size : 512 KB

 From numactl --hardware  WARNING: a numactl 'node' might or might not correspond to a
 physical chip.
   available: 4 nodes (0-3)
   node 0 cpus: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
   node 0 size: 64290 MB
   node 0 free: 64154 MB
   node 1 cpus: 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
   node 1 size: 64507 MB
   node 1 free: 64367 MB
   node 2 cpus: 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47
   node 2 size: 64507 MB
   node 2 free: 64211 MB
   node 3 cpus: 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63
   node 3 size: 64465 MB
   node 3 free: 64330 MB
   node distances:
   node   0   1   2   3
     0:  10  12  12  12
     1:  12  10  12  12
     2:  12  12  10  12
     3:  12  12  12  10

 From /proc/meminfo
    MemTotal:       263958144 kB
    HugePages_Total:       0
    Hugepagesize:       2048 kB

 From /etc/*release* /etc/*version*
    os-release:
       NAME="SLES"
       VERSION="15-SP1"
       VERSION_ID="15.1"
       PRETTY_NAME="SUSE Linux Enterprise Server 15 SP1"
       ID="sles"
       ID_LIKE="suse"
       ANSI_COLOR="0;32"
       CPE_NAME="cpe:/o:suse:sles:15:sp1"

 uname -a:
    Linux dl325gen10 4.12.14-195-default #1 SMP Tue May 7 10:55:11 UTC 2019 (8fba516)
    x86_64 x86_64 x86_64 GNU/Linux

 Kernel self-reported vulnerability status:

 CVE-2018-3620 (L1 Terminal Fault):        Not affected
 Microarchitectural Data Sampling:         Not affected
 CVE-2017-5754 (Meltdown):                 Not affected
 CVE-2018-3639 (Speculative Store Bypass): Mitigation: Speculative Store Bypass disabled
                                           via prctl and seccomp
 CVE-2017-5753 (Spectre variant 1):        Mitigation: __user pointer sanitization
 CVE-2017-5715 (Spectre variant 2):        Mitigation: Full AMD retpoline, IBPB:
                                           conditional, IBRS_FW, STIBP: disabled, RSB
                                           filling

 run-level 3 Aug 31 13:56

 SPEC is set to: /cpu2017
    Filesystem     Type   Size  Used Avail Use% Mounted on
    /dev/sda2      btrfs   40G   11G   29G  28% /

 From /sys/devices/virtual/dmi/id
     BIOS:    HPE A41 07/20/2019
     Vendor:  HPE
     Product: ProLiant DL325 Gen10
     Product Family: ProLiant
     Serial:  CN781302PS

 Additional information from dmidecode follows.  WARNING: Use caution when you interpret
 this section. The 'dmidecode' program reads system data which is "intended to allow
 hardware to be accurately determined", but the intent may not be met, as there are
 frequent changes to hardware, firmware, and the "DMTF SMBIOS" standard.
   Memory:
     8x UNKNOWN NOT AVAILABLE
     8x UNKNOWN NOT AVAILABLE 32 GB 2 rank 2933

 (End of data from sysinfo program)

Power Settings Notes

PTDaemon to measure power and temperature was run on a ProLiant DL360 Gen9 as a controller
with 2x Intel Xeon E5-2660 v3 CPU and 128 GB of memory using Windows Server 2012 R2.
Power management in the OS was disabled by setting Linux CPU governor to performance for all cores:
 cpupower frequency-set -r -g performance
Power management in the BIOS was default except for any settings mentioned in BIOS Configuration.
No power management settings were set in the management firmware.
The optional optical drive was not installed.
The system was configured with 7 HPE Small Form Factor Hard Drive Blanks (666987-B21), 8 DIMM blanks
2 high performance heatsinks and baffles that fit over the high performance
heatsinks in order to produce correct airflow and cooling.
The run was started and observed through the management firmware.
The Embedded SATA controller was the HPE Smart Array S100i SR Gen10 SW RAID.

Compiler Version Notes

==============================================================================
C               | 619.lbm_s(base, peak) 638.imagick_s(base, peak)
                | 644.nab_s(base, peak)
------------------------------------------------------------------------------
AOCC.LLVM.2.0.0.B191.2019_07_19 clang version 8.0.0 (CLANG: Jenkins
  AOCC_2_0_0-Build#191) (based on LLVM AOCC.LLVM.2.0.0.B191.2019_07_19)
Target: x86_64-unknown-linux-gnu
Thread model: posix
InstalledDir: /sppo/dev/compilers/aocc-compiler-2.0.0/bin
------------------------------------------------------------------------------

==============================================================================
C++, C, Fortran | 607.cactuBSSN_s(base, peak)
------------------------------------------------------------------------------
AOCC.LLVM.2.0.0.B191.2019_07_19 clang version 8.0.0 (CLANG: Jenkins
  AOCC_2_0_0-Build#191) (based on LLVM AOCC.LLVM.2.0.0.B191.2019_07_19)
Target: x86_64-unknown-linux-gnu
Thread model: posix
InstalledDir: /sppo/dev/compilers/aocc-compiler-2.0.0/bin
AOCC.LLVM.2.0.0.B191.2019_07_19 clang version 8.0.0 (CLANG: Jenkins
  AOCC_2_0_0-Build#191) (based on LLVM AOCC.LLVM.2.0.0.B191.2019_07_19)
Target: x86_64-unknown-linux-gnu
Thread model: posix
InstalledDir: /sppo/dev/compilers/aocc-compiler-2.0.0/bin
AOCC.LLVM.2.0.0.B191.2019_07_19 clang version 8.0.0 (CLANG: Jenkins
  AOCC_2_0_0-Build#191) (based on LLVM AOCC.LLVM.2.0.0.B191.2019_07_19)
Target: x86_64-unknown-linux-gnu
Thread model: posix
InstalledDir: /sppo/dev/compilers/aocc-compiler-2.0.0/bin
------------------------------------------------------------------------------

==============================================================================
Fortran         | 603.bwaves_s(base, peak) 649.fotonik3d_s(base, peak)
                | 654.roms_s(base, peak)
------------------------------------------------------------------------------
AOCC.LLVM.2.0.0.B191.2019_07_19 clang version 8.0.0 (CLANG: Jenkins
  AOCC_2_0_0-Build#191) (based on LLVM AOCC.LLVM.2.0.0.B191.2019_07_19)
Target: x86_64-unknown-linux-gnu
Thread model: posix
InstalledDir: /sppo/dev/compilers/aocc-compiler-2.0.0/bin
------------------------------------------------------------------------------

==============================================================================
Fortran, C      | 621.wrf_s(base, peak) 627.cam4_s(base, peak)
                | 628.pop2_s(base, peak)
------------------------------------------------------------------------------
AOCC.LLVM.2.0.0.B191.2019_07_19 clang version 8.0.0 (CLANG: Jenkins
  AOCC_2_0_0-Build#191) (based on LLVM AOCC.LLVM.2.0.0.B191.2019_07_19)
Target: x86_64-unknown-linux-gnu
Thread model: posix
InstalledDir: /sppo/dev/compilers/aocc-compiler-2.0.0/bin
AOCC.LLVM.2.0.0.B191.2019_07_19 clang version 8.0.0 (CLANG: Jenkins
  AOCC_2_0_0-Build#191) (based on LLVM AOCC.LLVM.2.0.0.B191.2019_07_19)
Target: x86_64-unknown-linux-gnu
Thread model: posix
InstalledDir: /sppo/dev/compilers/aocc-compiler-2.0.0/bin
------------------------------------------------------------------------------

Base Compiler Invocation

C benchmarks:

 clang 

Fortran benchmarks:

 flang 

Benchmarks using both Fortran and C:

 flang   clang 

Benchmarks using Fortran, C, and C++:

 clang++   clang   flang 

Base Portability Flags

603.bwaves_s:  -DSPEC_LP64 
607.cactuBSSN_s:  -DSPEC_LP64 
619.lbm_s:  -DSPEC_LP64 
621.wrf_s:  -DSPEC_CASE_FLAG   -Mbyteswapio   -DSPEC_LP64 
627.cam4_s:  -DSPEC_CASE_FLAG   -DSPEC_LP64 
628.pop2_s:  -DSPEC_CASE_FLAG   -Mbyteswapio   -DSPEC_LP64 
638.imagick_s:  -DSPEC_LP64 
644.nab_s:  -DSPEC_LP64 
649.fotonik3d_s:  -DSPEC_LP64 
654.roms_s:  -DSPEC_LP64 

Base Optimization Flags

C benchmarks:

 -flto   -Wl,-mllvm -Wl,-function-specialize   -Wl,-mllvm -Wl,-region-vectorize   -Wl,-mllvm -Wl,-vector-library=LIBMVEC   -Wl,-mllvm -Wl,-reduce-array-computations=3   -O3   -ffast-math   -march=znver2   -fstruct-layout=3   -mllvm -unroll-threshold=50   -fremap-arrays   -mllvm -function-specialize   -mllvm -enable-gvn-hoist   -mllvm -reduce-array-computations=3   -mllvm -global-vectorize-slp   -mllvm -vector-library=LIBMVEC   -mllvm -inline-threshold=1000   -flv-function-specialization   -z muldefs   -DSPEC_OPENMP   -fopenmp   -DUSE_OPENMP   -fopenmp=libomp   -lomp   -lpthread   -ldl   -lmvec   -lamdlibm   -ljemalloc   -lflang 

Fortran benchmarks:

 -flto   -Wl,-mllvm -Wl,-function-specialize   -Wl,-mllvm -Wl,-region-vectorize   -Wl,-mllvm -Wl,-vector-library=LIBMVEC   -Wl,-mllvm -Wl,-reduce-array-computations=3   -O3   -march=znver2   -funroll-loops   -Mrecursive   -mllvm -vector-library=LIBMVEC   -z muldefs   -Kieee   -fno-finite-math-only   -DSPEC_OPENMP   -fopenmp   -DUSE_OPENMP   -fopenmp=libomp   -lomp   -lpthread   -ldl   -lmvec   -lamdlibm   -ljemalloc   -lflang 

Benchmarks using both Fortran and C:

 -flto   -Wl,-mllvm -Wl,-function-specialize   -Wl,-mllvm -Wl,-region-vectorize   -Wl,-mllvm -Wl,-vector-library=LIBMVEC   -Wl,-mllvm -Wl,-reduce-array-computations=3   -O3   -ffast-math   -march=znver2   -fstruct-layout=3   -mllvm -unroll-threshold=50   -fremap-arrays   -mllvm -function-specialize   -mllvm -enable-gvn-hoist   -mllvm -reduce-array-computations=3   -mllvm -global-vectorize-slp   -mllvm -vector-library=LIBMVEC   -mllvm -inline-threshold=1000   -flv-function-specialization   -funroll-loops   -Mrecursive   -z muldefs   -Kieee   -fno-finite-math-only   -DSPEC_OPENMP   -fopenmp   -DUSE_OPENMP   -fopenmp=libomp   -lomp   -lpthread   -ldl   -lmvec   -lamdlibm   -ljemalloc   -lflang 

Benchmarks using Fortran, C, and C++:

 -std=c++98   -flto   -Wl,-mllvm -Wl,-function-specialize   -Wl,-mllvm -Wl,-region-vectorize   -Wl,-mllvm -Wl,-vector-library=LIBMVEC   -Wl,-mllvm -Wl,-reduce-array-computations=3   -Wl,-mllvm -Wl,-suppress-fmas   -O3   -ffast-math   -march=znver2   -fstruct-layout=3   -mllvm -unroll-threshold=50   -fremap-arrays   -mllvm -function-specialize   -mllvm -enable-gvn-hoist   -mllvm -reduce-array-computations=3   -mllvm -global-vectorize-slp   -mllvm -vector-library=LIBMVEC   -mllvm -inline-threshold=1000   -flv-function-specialization   -mllvm -loop-unswitch-threshold=200000   -mllvm -unroll-threshold=100   -mllvm -enable-partial-unswitch   -funroll-loops   -Mrecursive   -z muldefs   -Kieee   -fno-finite-math-only   -DSPEC_OPENMP   -fopenmp   -DUSE_OPENMP   -fopenmp=libomp   -lomp   -lpthread   -ldl   -lmvec   -lamdlibm   -ljemalloc   -lflang 

Base Other Flags

C benchmarks:

 -Wno-return-type 

Fortran benchmarks:

 -Wno-return-type 

Benchmarks using both Fortran and C:

 -Wno-return-type 

Benchmarks using Fortran, C, and C++:

 -Wno-return-type 

Peak Compiler Invocation

C benchmarks:

 clang 

Fortran benchmarks:

 flang 

Benchmarks using both Fortran and C:

 flang   clang 

Benchmarks using Fortran, C, and C++:

 clang++   clang   flang 

Peak Portability Flags

Same as Base Portability Flags

Peak Optimization Flags

C benchmarks:

619.lbm_s:  basepeak = yes 
638.imagick_s:  basepeak = yes 
644.nab_s:  basepeak = yes 

Fortran benchmarks:

603.bwaves_s:  basepeak = yes 
649.fotonik3d_s:  basepeak = yes 
654.roms_s:  -flto   -Wl,-mllvm -Wl,-function-specialize   -Wl,-mllvm -Wl,-region-vectorize   -Wl,-mllvm -Wl,-vector-library=LIBMVEC   -Wl,-mllvm -Wl,-reduce-array-computations=3   -Wl,-mllvm -Wl,-enable-X86-prefetching   -O3   -march=znver2   -funroll-loops   -Mrecursive   -mllvm -vector-library=LIBMVEC   -Kieee   -fno-finite-math-only   -DSPEC_OPENMP   -fopenmp   -DUSE_OPENMP   -fopenmp=libomp   -lomp   -lpthread   -ldl   -lmvec   -lamdlibm   -ljemalloc   -lflang 

Benchmarks using both Fortran and C:

621.wrf_s:  -flto   -Wl,-mllvm -Wl,-function-specialize   -Wl,-mllvm -Wl,-region-vectorize   -Wl,-mllvm -Wl,-vector-library=LIBMVEC   -Wl,-mllvm -Wl,-reduce-array-computations=3   -Ofast   -march=znver2   -mno-sse4a   -fstruct-layout=5   -mllvm -vectorize-memory-aggressively   -mllvm -function-specialize   -mllvm -enable-gvn-hoist   -mllvm -unroll-threshold=50   -fremap-arrays   -mllvm -vector-library=LIBMVEC   -mllvm -reduce-array-computations=3   -mllvm -global-vectorize-slp   -mllvm -inline-threshold=1000   -flv-function-specialization   -O3   -funroll-loops   -Mrecursive   -Kieee   -fno-finite-math-only   -DSPEC_OPENMP   -fopenmp   -DUSE_OPENMP   -fopenmp=libomp   -lomp   -lpthread   -ldl   -lmvec   -lamdlibm   -ljemalloc   -lflang 
627.cam4_s:  basepeak = yes 
628.pop2_s:  basepeak = yes 

Benchmarks using Fortran, C, and C++:

 -std=c++98   -flto   -Wl,-mllvm -Wl,-function-specialize   -Wl,-mllvm -Wl,-region-vectorize   -Wl,-mllvm -Wl,-vector-library=LIBMVEC   -Wl,-mllvm -Wl,-reduce-array-computations=3   -Ofast   -march=znver2   -mno-sse4a   -fstruct-layout=5   -mllvm -vectorize-memory-aggressively   -mllvm -function-specialize   -mllvm -enable-gvn-hoist   -mllvm -unroll-threshold=50   -fremap-arrays   -mllvm -vector-library=LIBMVEC   -mllvm -reduce-array-computations=3   -mllvm -global-vectorize-slp   -mllvm -inline-threshold=1000   -flv-function-specialization   -mllvm -unroll-threshold=100   -mllvm -enable-partial-unswitch   -mllvm -loop-unswitch-threshold=200000   -O3   -funroll-loops   -Mrecursive   -Kieee   -fno-finite-math-only   -DSPEC_OPENMP   -fopenmp   -DUSE_OPENMP   -fopenmp=libomp   -lomp   -lpthread   -ldl   -lmvec   -lamdlibm   -ljemalloc   -lflang 

Peak Other Flags

C benchmarks:

 -Wno-return-type 

Fortran benchmarks:

 -Wno-return-type 

Benchmarks using both Fortran and C:

 -Wno-return-type 

Benchmarks using Fortran, C, and C++:

 -Wno-return-type 

The flags files that were used to format this result can be browsed at
http://www.spec.org/cpu2017/flags/aocc200-flags-C1-HPE.html,
http://www.spec.org/cpu2017/flags/HPE-Platform-Flags-AMD-V1.2-EPYC-revF.html.

You can also download the XML flags sources by saving the following links:
http://www.spec.org/cpu2017/flags/aocc200-flags-C1-HPE.xml,
http://www.spec.org/cpu2017/flags/HPE-Platform-Flags-AMD-V1.2-EPYC-revF.xml.

PTDaemon, SPEC CPU, and SPECspeed are trademarks or registered trademarks of the Standard Performance Evaluation Corporation. All other brand and product names appearing in this result are trademarks or registered trademarks of their respective holders.

For questions about this result, please contact the tester. For other inquiries, please contact [email protected]
Copyright 2017-2019 Standard Performance Evaluation Corporation
Tested with SPEC CPU®2017 v1.1.0 on 2019-08-31 20:41:37-0400.
Report generated on 2019-09-17 16:19:28 by SPEC CPU®2017 HTML formatter v6255.
Originally published on 2019-09-17.