# Invocation command line:
# /home/cpu2006/bin/runspec --flagsurl=Intel-ic16.0-official-linux64.xml,NEC-Platform-Settings-V1.2-120g-RevB.xml --rate 28 -c cpu2006-1.2-ic16.0-lin64-ws-avx2-rate-20150812.cfg --define smt --define cores=14 --define physicalfirst --define no-numa --define THP_enabled -T all -o all fp
# output_root was not used for this run
############################################################################
############################################################################
# This is a sample config file. It was tested with:
#
#      Compiler name/version:       Intel Compiler 16.0
#      Operating system version:    64-Bit RedHat Enterprise Linux64 7.1
#      Hardware:                    Intel processors supporting AVX2
#
############################################################################
# SPEC CPU2006 Intel Linux64 config file
# 20150812 Intel Compiler 16.0 for Linux64
############################################################################
action      = validate
tune        = base,peak

     #
     ########################################################
     #         ATTENTION     ATTENTION     ATTENTION
     ########################################################
     #
     #     NOTE If you change fail_build then PLEASE also
     #     change the line 'define version', because
     #     SPEC review tools use 'ext' to track binaries.
     #
     ########################################################
%define version 20150812
     ext         = cpu2006-1.2-ic16.0-lin64-ws-avx2-rate-%{version}
     #
     # vvvvvvvvvvvv # do not change unless you read NOTE above
       fail_build=1 # do not change unless you read NOTE above
     # ^^^^^^^^^^^^ # do not change unless you read NOTE above
     #
     ########################################################
     #

#####################################################################################
# You can't change the line with fail_build=1 without changing the line ext=
# to reflect the data on which you re-built the binaries.
# In addition, the sw_compiler lines below, must be modified to match the description
# of the compiler being used to build the binaries
#####################################################################################
PATHSEP     = /
check_md5=1
reportable=1
bench_post_setup=sync
parallel_test=0
mean_anyway=1
sysinfo_program = specperl $[top]/config/sysinfo.rev6914 -f -p

flagsurl000=http://www.spec.org/cpu2006/flags/Intel-ic16.0-official-linux64.xml
%ifdef %{default-platform-flags}
flagsurl2=Default-Platform-Flags.xml
%endif

# Set some environment variables
preENV_LD_LIBRARY_PATH = $[top]/libs/32:$[top]/libs/64:$[top]/sh

#
# These are listed as benchmark-tuning-extension-machine
#
int=default=default=default:
CC=  icc -m32 -L/opt/intel/compilers_and_libraries_2016/linux/compiler/lib/ia32_lin
CXX= icpc -m32 -L/opt/intel/compilers_and_libraries_2016/linux/compiler/lib/ia32_lin
OBJ = .o
SMARTHEAP32_DIR = /sh
SMARTHEAP64_DIR = /sh
PORTABILITY = -D_FILE_OFFSET_BITS=64

fp=default=default=default:
CC=  icc   -m64
CXX= icpc  -m64
FC=  ifort -m64
OBJ = .o

# For UP systems, we need to know if the processors are ordered across cores first or in order
# If across cores, processors 0, 1, 2 and 3 are on distinct physical cores
# Otherwise, processors 0, 2, 4 and 6 are on distinct physical cores

default:
submit       = numactl --localalloc --physcpubind=$SPECCOPYNUM $command

%ifdef %{no-numa}
submit       = taskset -c $SPECCOPYNUM $command
%endif

####################################################################
# Compiler options
# for Nehalem use -xSSE4.2
# for processors prior to dunnington, replace -xSSE4.1 with -xSSSE3
####################################################################
default:
SSE          = -xCORE-AVX2
FASTNOSTATIC =  $(SSE) -ipo -O3 -no-prec-div
FAST         =  $(SSE) -ipo -O3 -no-prec-div

################################################################
#
# portability & libraries
#
#################### Portability Flags and Notes ############################

400.perlbench=default:
CPORTABILITY=      -DSPEC_CPU_LINUX_IA32

403.gcc=default:
EXTRA_CFLAGS=      -Dalloca=_alloca

462.libquantum=default:
CPORTABILITY=      -DSPEC_CPU_LINUX

483.xalancbmk=default:
CXXPORTABILITY=    -DSPEC_CPU_LINUX

fp=default:
PORTABILITY = -DSPEC_CPU_LP64

435.gromacs=default=default=default:
LDPORTABILITY = -nofor_main

436.cactusADM=default=default=default:
LDPORTABILITY = -nofor_main

454.calculix=default=default=default:
LDPORTABILITY = -nofor_main

481.wrf=default=default=default:
CPORTABILITY = -DSPEC_CPU_CASE_FLAG -DSPEC_CPU_LINUX


################################################################
# Tuning Flags
################################################################
#
# Base tuning default optimization
# Feedback directed optimization not allowed in baseline for CPU2006
# However there is no limit on the number of flags as long as the same
# flags are used in the same order for all benchmarks of a given language

471.omnetpp,473.astar,483.xalancbmk=default:
EXTRA_LIBS=  -L$(SMARTHEAP32_DIR) -lsmartheap
EXTRA_LDFLAGS= -Wl,-z,muldefs

int=base=default=default:
COPTIMIZE=    $(FASTNOSTATIC)  -opt-prefetch -opt-mem-layout-trans=3
CXXOPTIMIZE=  $(FASTNOSTATIC)  -opt-prefetch -opt-mem-layout-trans=3

fp=base=default=default:
OPTIMIZE=     $(FAST) -opt-prefetch
COPTIMIZE=    -auto-p32 -ansi-alias -opt-mem-layout-trans=3
CXXOPTIMIZE=  -auto-p32 -ansi-alias -opt-mem-layout-trans=3

################################################################
# Peak Tuning Flags int 2006 fast
################################################################
int=peak=default:
COPTIMIZE=         -ansi-alias -opt-mem-layout-trans=3
CXXOPTIMIZE=       -ansi-alias -opt-mem-layout-trans=3
PASS1_CFLAGS     = -prof-gen:threadsafe -par-num-threads=1
PASS2_CFLAGS     = $(FASTNOSTATIC) -prof-use
PASS1_CXXFLAGS   = -prof-gen:threadsafe -par-num-threads=1
PASS2_CXXFLAGS   = $(FASTNOSTATIC) -prof-use
PASS1_LDCFLAGS   = -prof-gen:threadsafe -par-num-threads=1
PASS2_LDCFLAGS   = $(FASTNOSTATIC) -prof-use
PASS1_LDCXXFLAGS = -prof-gen:threadsafe -par-num-threads=1
PASS2_LDCXXFLAGS = $(FASTNOSTATIC) -prof-use

400.perlbench=peak=default:
CC= icc -m64
CPORTABILITY= -DSPEC_CPU_LP64 -DSPEC_CPU_LINUX_X64
COPTIMIZE= -auto-ilp32

401.bzip2=peak=default:
CC= icc -m64
CPORTABILITY= -DSPEC_CPU_LP64
COPTIMIZE= -opt-prefetch  -auto-ilp32 -ansi-alias

403.gcc=peak=default:
COPTIMIZE = $(FASTNOSTATIC)
feedback=0

429.mcf=peak=default:
basepeak=yes

445.gobmk=peak=default:
PASS1_CFLAGS     = -prof-gen:threadsafe -par-num-threads=1
PASS2_CFLAGS     = $(SSE) -prof-use
PASS1_LDCFLAGS   = -prof-gen:threadsafe -par-num-threads=1
PASS2_LDCFLAGS   = $(SSE) -prof-use

456.hmmer=peak=default:
CC= icc -m64
CPORTABILITY= -DSPEC_CPU_LP64
COPTIMIZE=  $(FASTNOSTATIC) -unroll2  -auto-ilp32
feedback=no

458.sjeng=peak=default:
CC= icc -m64
CPORTABILITY= -DSPEC_CPU_LP64
COPTIMIZE= -unroll4 -auto-ilp32

462.libquantum=peak=default:
basepeak=yes

464.h264ref=peak=default:
COPTIMIZE=  -unroll2 -ansi-alias

471.omnetpp=peak=default:
CXXOPTIMIZE=  -ansi-alias -opt-ra-region-strategy=block

473.astar=peak=default:
basepeak=yes

483.xalancbmk=peak=default:
basepeak=yes

################################################################
# Peak Tuning Flags for FP
################################################################
fp=peak=default:
COPTIMIZE=       -auto-ilp32
CXXOPTIMIZE=     -auto-ilp32
PASS1_CFLAGS =   -prof-gen:threadsafe -par-num-threads=1
PASS2_CFLAGS =   $(FASTNOSTATIC) -opt-mem-layout-trans=3 -prof-use
PASS1_CXXFLAGS = -prof-gen:threadsafe -par-num-threads=1
PASS2_CXXFLAGS = $(FASTNOSTATIC) -opt-mem-layout-trans=3 -prof-use
PASS1_FFLAGS =   -prof-gen:threadsafe -par-num-threads=1
PASS2_FFLAGS =   $(FASTNOSTATIC)                         -prof-use
PASS1_LDFLAGS =  -prof-gen:threadsafe -par-num-threads=1
PASS2_LDFLAGS =  $(FASTNOSTATIC)                         -prof-use

410.bwaves=peak=default:
basepeak=yes
####################################################################################################################################
%ifdef %{smt}
copies=%{cores}
%ifdef %{physicallogical}
submit       = numactl --localalloc --physcpubind=`expr 2 \\* $SPECCOPYNUM` $command
%ifdef %{no-numa}
submit       = taskset -c `expr 2 \\* $SPECCOPYNUM` $command
%endif
%endif
%endif
####################################################################################################################################

416.gamess=peak=default:
OPTIMIZE= -unroll2 -inline-level=0  -scalar-rep-

433.milc=peak=default:
basepeak=yes

434.zeusmp=peak=default:
basepeak=yes
feedback=0

435.gromacs=peak=default:
OPTIMIZE= -opt-prefetch

436.cactusADM=peak=default:
basepeak=yes

437.leslie3d=peak=default:
basepeak=yes

####################################################################################################################################
%ifdef %{smt}
copies=%{cores}
%ifdef %{physicallogical}
submit       = numactl --localalloc --physcpubind=`expr 2 \\* $SPECCOPYNUM` $command
%ifdef %{no-numa}
submit       = taskset -c `expr 2 \\* $SPECCOPYNUM` $command
%endif
%endif
%endif
####################################################################################################################################

444.namd=peak=default:
CXXOPTIMIZE= -fno-alias -auto-ilp32

447.dealII=peak=default:
basepeak=yes

450.soplex=peak=default:
PORTABILITY = -D_FILE_OFFSET_BITS=64
CXX= icpc -m32 -L/opt/intel/compilers_and_libraries_2016/linux/compiler/lib/ia32_lin
OPTIMIZE= -opt-malloc-options=3
CXXOPTIMIZE=
####################################################################################################################################
%ifdef %{smt}
copies=%{cores}
%ifdef %{physicallogical}
submit       = numactl --localalloc --physcpubind=`expr 2 \\* $SPECCOPYNUM` $command
%ifdef %{no-numa}
submit       = taskset -c `expr 2 \\* $SPECCOPYNUM` $command
%endif
%endif
%endif
####################################################################################################################################

453.povray=peak=default:
CXXOPTIMIZE= -unroll4  -ansi-alias

454.calculix=peak=default:
basepeak=yes

459.GemsFDTD=peak=default:
basepeak=yes
####################################################################################################################################
%ifdef %{smt}
copies=%{cores}
%ifdef %{physicallogical}
submit       = numactl --localalloc --physcpubind=`expr 2 \\* $SPECCOPYNUM` $command
%ifdef %{no-numa}
submit       = taskset -c `expr 2 \\* $SPECCOPYNUM` $command
%endif
%endif
%endif
####################################################################################################################################

465.tonto=peak=default:
OPTIMIZE= -unroll4 -auto -inline-calloc -opt-malloc-options=3

470.lbm=peak=default:
basepeak=yes

481.wrf=peak=default:
basepeak=yes

482.sphinx3=peak=default:
basepeak=yes

#################################################################
# (Edit this to match your system)
#################################################################

default=default=default=default:
#include: SUT.inc
#  ----- Begin inclusion of 'SUT.inc'
############################################################################
default=default=default=default:
license_num      = 9006
test_sponsor     = NEC Corporation
hw_avail         = Apr-2016
sw_avail         = Jan-2016
tester           = NEC Corporation
hw_cpu_name      = Intel Xeon E5-2690 v4
# hw_cpu_char      =
# hw_cpu_char      = Intel Turbo Boost Technology disabled
hw_cpu_char      = Intel Turbo Boost Technology up to 3.50 GHz
hw_cpu_mhz       = 2600
hw_disk          = 1 x 1 TB SATA, 7200 RPM
hw_fpu           = Integrated
hw_memory        = 128 GB (8 x 16 GB 2Rx4 PC4-2400T-R)
hw_model         = Express5800/R120g-1M (Intel Xeon E5-2690 v4)
hw_ncpuorder     = 1,2 chips
hw_ncores        = 14
hw_nchips        = 1
hw_ncoresperchip = 14
hw_nthreadspercore = 2
hw_other         = None
hw_pcache        = 32 KB I + 32 KB D on chip per core
hw_scache        = 256 KB I+D on chip per core
hw_tcache        = 35 MB I+D on chip per chip
hw_ocache        = None
hw_vendor        = NEC Corporation
prepared_by      = NEC Corporation
sw_file          = ext4
sw_os000         = Red Hat Enterprise Linux Server release 7.2
sw_os001 = (Maipo)
sw_os002         = Kernel 3.10.0-327.4.5.el7.x86_64
sw_state         = Run level 3 (multi-user)

# notes_plat_000 = Default BIOS settings were used.
notes_plat_000   = BIOS Settings:
notes_plat_005   =  Power Management Policy: Custom
notes_plat_010   =  Energy Performance: Performance
notes_plat_015   =  Patrol Scrub: Disabled
# notes_plat_020   =  Demand Scrub: Disabled
# notes_plat_025   =  Cluster on Die: Enabled
# notes_plat_030   =  Snoop Mode: Home Snoop
# notes_plat_030   =  Snoop Mode: Home Snoop with Directory
# notes_plat_035   =  Hyper-Threading: Disabled

notes_025        =
notes_030        = The Express5800/R120g-1M (Intel Xeon E5-2690 v4) and
notes_035        = the Express5800/R120g-2M (Intel Xeon E5-2690 v4) models are electronically equivalent.
notes_040        = The results have been measured on the Express5800/R120g-2M (Intel Xeon E5-2690 v4) model.
notes_045        =

# ---- End inclusion of '/home/cpu2006/config/SUT.inc'
notes_submit_000 = The numactl mechanism was used to bind copies to processors. The config file option 'submit'
notes_submit_001 = was used to generate numactl commands to bind each copy to a specific processor.
notes_submit_002 = For details, please see the config file.
%ifdef %{no-numa}
notes_submit_000 = The taskset mechanism was used to bind copies to processors. The config file option 'submit'
notes_submit_005 = was used to generate taskset commands to bind each copy to a specific processor.
notes_submit_010 = For details, please see the config file.
%endif
notes_015        = Binaries compiled on a system with 1x Intel Core i5-4670K CPU + 32GB
notes_020        = memory using RedHat EL 7.1
notes_os_000     = Stack size set to unlimited using "ulimit -s unlimited"

int=default=default=default:
sw_compiler001   = C/C++: Version 16.0.0.101 of Intel C++ Studio XE
sw_compiler002   = for Linux
sw_base_ptrsize  = 32-bit
sw_peak_ptrsize  = 32/64-bit
sw_other001      = Microquill SmartHeap V10.2

default:
%ifdef %{THP_enabled}
notes_050        = Transparent Huge Pages enabled with:
notes_055        = echo always > /sys/kernel/mm/transparent_hugepage/enabled
%endif

%ifdef %{THP_disabled}
notes_200        = Transparent Huge Pages disabled with:
notes_201        = echo never  > /sys/kernel/mm/transparent_hugepage/enabled
%endif

%ifdef %{drop_caches}
notes_202        = Filesystem page cache cleared with:
notes_203        = echo 1 >       /proc/sys/vm/drop_caches
%endif

%ifdef %{invoke_with_interleave}
notes_204        = runspec command invoked through numactl i.e.:
notes_205        = numactl --interleave=all runspec <etc>
%endif

fp=default=default=default:
sw_compiler000   = C/C++: Version 16.0.0.101 of Intel C++ Studio XE
sw_compiler001   = for Linux;
sw_compiler002   = Fortran: Version 16.0.0.101 of Intel Fortran
sw_compiler003   = Studio XE for Linux
sw_base_ptrsize  = 32/64-bit
sw_peak_ptrsize  = 32/64-bit
sw_other         = None


# The following settings were obtained by running 'specperl $[top]/config/sysinfo.rev6914 -f -p'
default:
# Sysinfo program /home/cpu2006/config/sysinfo.rev6914
# $Rev: 6914 $ $Date:: 2014-06-25 #$ e3fbb8667b5a285932ceab81e28219e1
# running on r120g-m Wed May 11 17:41:35 2016
#
# This section contains SUT (System Under Test) info as seen by
# some common utilities.  To remove or add to this section, see:
#   http://www.spec.org/cpu2006/Docs/config.html#sysinfo
#
# From /proc/cpuinfo
#    model name : Intel(R) Xeon(R) CPU E5-2690 v4@ 2.60GHz
#       1 "physical id"s (chips)
#       28 "processors"
#    cores, siblings (Caution: counting these is hw and system dependent.  The
#    following excerpts from /proc/cpuinfo might not be reliable.  Use with
#    caution.)
#       cpu cores : 14
#       siblings  : 28
#       physical 0: cores 0 1 2 3 4 5 6 8 9 10 11 12 13 14
#    cache size : 35840 KB
#
# From /proc/meminfo
#    MemTotal:       131915400 kB
#    HugePages_Total:       0
#    Hugepagesize:       2048 kB
#
# From /etc/*release* /etc/*version*
#    os-release:
#       NAME="Red Hat Enterprise Linux Server"
#       VERSION="7.2 (Maipo)"
#       ID="rhel"
#       ID_LIKE="fedora"
#       VERSION_ID="7.2"
#       PRETTY_NAME="Red Hat Enterprise Linux Server 7.2 (Maipo)"
#       ANSI_COLOR="0;31"
#       CPE_NAME="cpe:/o:redhat:enterprise_linux:7.2:GA:server"
#    redhat-release: Red Hat Enterprise Linux Server release 7.2 (Maipo)
#    system-release: Red Hat Enterprise Linux Server release 7.2 (Maipo)
#    system-release-cpe: cpe:/o:redhat:enterprise_linux:7.2:ga:server
#
# uname -a:
#    Linux r120g-m 3.10.0-327.4.5.el7.x86_64 #1 SMP Thu Jan 21 04:10:29 EST 2016
#    x86_64 x86_64 x86_64 GNU/Linux
#
# run-level 3 May 11 17:36
#
# SPEC is set to: /home/cpu2006
#    Filesystem     Type  Size  Used Avail Use% Mounted on
#    /dev/sda3      ext4  909G  259G  604G  30% /
# Additional information from dmidecode:
#
#    Warning: Use caution when you interpret this section. The 'dmidecode' program
#    reads system data which is "intended to allow hardware to be accurately
#    determined", but the intent may not be met, as there are frequent changes to
#    hardware, firmware, and the "DMTF SMBIOS" standard.
#
#   BIOS American Megatrends Inc. 5.0.1005 01/15/2016
#   Memory:
#    8x Samsung M393A2G40DB1-CRC 16 GB 2 rank 2400 MHz
#
# (End of data from sysinfo program)
# hw_cpu_name    = Intel Xeon E5-2690 v4
# hw_disk        = 909 GB  add more disk info here
# hw_memory001   = 125.804 GB fixme: If using DDR3, format is:
# hw_memory002   = 'N GB (M x N GB nRxn PCn-nnnnnR-n, ECC)'
# hw_nchips      = 1
# prepared_by    = root  (is never output, only tags rawfile)
# sw_file        = ext4
# sw_os001       = Red Hat Enterprise Linux Server release 7.2 (Maipo)
# sw_os002       = 3.10.0-327.4.5.el7.x86_64
# sw_state       = Run level 3 (add definition here)


# The following section was added automatically, and contains settings that
# did not appear in the original configuration file, but were added to the
# raw file after the run.
default:
flagsurl001 = http://www.spec.org/cpu2006/flags/NEC-Platform-Settings-V1.2-120g-RevC.xml
notes_000 =Environment variables set by runspec before the start of the run:
notes_005 =LD_LIBRARY_PATH = "/home/cpu2006/libs/32:/home/cpu2006/libs/64:/home/cpu2006/sh"
notes_010 =