# Invocation command line:
# /home/SPECcpu2006/bin/runspec --define invoke_with_interleave --define default-platform-flags --rate 24 -c cpu2006.1.2.ic15.linux64.ws.avx2.rate.29aug2014.cfg --define smt --define cores=12 --define physicalfirst --define invoke_with_interleave --define drop_caches --define THP_enabled -T all -o all fp
# output_root was not used for this run
############################################################################
############################################################################
# This is a sample config file. It was tested with:
#
#      Compiler name/version:       Intel Compiler 15
#      Operating system version:    64-Bit RedHat Enterprise Linux64 6.4
#      Hardware:                    Intel processors supporting AVX2
#
############################################################################
# SPEC CPU2006 Intel Linux64 config file
# Aug 2012 IC 13 Linux64
############################################################################
action      = validate
tune        = base,peak

     #
     ########################################################
     #         ATTENTION     ATTENTION     ATTENTION
     ########################################################
     #
     #     NOTE If you change fail_build then PLEASE also
     #     change the line 'define version', because
     #     SPEC review tools use 'ext' to track binaries.
     #
     ########################################################
%define version 29aug2014
     ext         = cpu2006.1.2.ic15.linux64.ws.avx2.rate.%{version}
     #
     # vvvvvvvvvvvv # do not change unless you read NOTE above
       fail_build=1 # do not change unless you read NOTE above
     # ^^^^^^^^^^^^ # do not change unless you read NOTE above
     #
     ########################################################
     #

#####################################################################################
# You can't change the line with fail_build=1 without changing the line ext=
# to reflect the data on which you re-built the binaries.
# In addition, the sw_compiler lines below, must be modified to match the description
# of the compiler being used to build the binaries
#####################################################################################
PATHSEP     = /
check_md5=1
reportable=1
bench_post_setup=sync
parallel_test=0
mean_anyway=1
sysinfo_program = specperl $[top]/config/sysinfo.rev6914 -p -f

flagsurl000=http://www.spec.org/cpu2006/flags/Intel-ic15.0-official-linux64.xml
%ifdef %{default-platform-flags}
flagsurl001=http://www.spec.org/cpu2006/flags/Fujitsu-Platform-Settings-V1.2-HSW-RevA.xml
%endif

# Set some environment variables
preENV_LD_LIBRARY_PATH = $[top]/libs/32:$[top]/libs/64:$[top]/sh

#
# These are listed as benchmark-tuning-extension-machine
#
int=default=default=default:
CC=  icc -m32 -L/opt/intel/composer_xe_2015/lib/ia32
CXX= icpc -m32 -L/opt/intel/composer_xe_2015/lib/ia32
OBJ = .o
SMARTHEAP32_DIR = /sh
SMARTHEAP64_DIR = /sh

fp=default=default=default:
CC=  icc   -m64
CXX= icpc  -m64
FC=  ifort -m64
OBJ = .o

# For UP systems, we need to know if the processors are ordered across cores first or in order
# If across cores, processors 0, 1, 2 and 3 are on distinct physical cores
# Otherwise, processors 0, 2, 4 and 6 are on distinct physical cores

default:
submit       = numactl --localalloc --physcpubind=$SPECCOPYNUM $command

%ifdef %{no-numa}
submit       = taskset -c $SPECCOPYNUM $command
%endif

####################################################################
# Compiler options
# for Nehalem use -xSSE4.2
# for processors prior to dunnington, replace -xSSE4.1 with -xSSSE3
####################################################################
default:
SSE          = -xCORE-AVX2
FASTNOSTATIC =  $(SSE) -ipo -O3 -no-prec-div
FAST         =  $(SSE) -ipo -O3 -no-prec-div

################################################################
#
# portability & libraries
#
#################### Portability Flags and Notes ############################

400.perlbench=default:
CPORTABILITY=      -DSPEC_CPU_LINUX_IA32

403.gcc=default:
EXTRA_CFLAGS=      -Dalloca=_alloca

462.libquantum=default:
CPORTABILITY=      -DSPEC_CPU_LINUX

483.xalancbmk=default:
CXXPORTABILITY=    -DSPEC_CPU_LINUX

fp=default:
PORTABILITY = -DSPEC_CPU_LP64

435.gromacs=default=default=default:
LDPORTABILITY = -nofor_main

436.cactusADM=default=default=default:
LDPORTABILITY = -nofor_main

454.calculix=default=default=default:
LDPORTABILITY = -nofor_main

481.wrf=default=default=default:
CPORTABILITY = -DSPEC_CPU_CASE_FLAG -DSPEC_CPU_LINUX


################################################################
# Tuning Flags
################################################################
#
# Base tuning default optimization
# Feedback directed optimization not allowed in baseline for CPU2006
# However there is no limit on the number of flags as long as the same
# flags are used in the same order for all benchmarks of a given language

471.omnetpp,473.astar,483.xalancbmk=default:
EXTRA_LIBS=  -L$(SMARTHEAP32_DIR) -lsmartheap
EXTRA_LDFLAGS= -Wl,-z,muldefs

int=base=default=default:
COPTIMIZE=    $(FASTNOSTATIC)  -opt-prefetch -opt-mem-layout-trans=3
CXXOPTIMIZE=  $(FASTNOSTATIC)  -opt-prefetch -opt-mem-layout-trans=3

fp=base=default=default:
OPTIMIZE=     $(FAST) -opt-prefetch
COPTIMIZE=    -auto-p32 -ansi-alias -opt-mem-layout-trans=3
CXXOPTIMIZE=  -auto-p32 -ansi-alias -opt-mem-layout-trans=3

################################################################
# Peak Tuning Flags int 2006 fast
################################################################
int=peak=default:
COPTIMIZE=         -ansi-alias -opt-mem-layout-trans=3
CXXOPTIMIZE=       -ansi-alias -opt-mem-layout-trans=3
PASS1_CFLAGS     = -prof-gen
PASS2_CFLAGS     = $(FASTNOSTATIC) -prof-use
PASS1_CXXFLAGS   = -prof-gen
PASS2_CXXFLAGS   = $(FASTNOSTATIC) -prof-use
PASS1_LDCFLAGS   = -prof-gen
PASS2_LDCFLAGS   = $(FASTNOSTATIC) -prof-use
PASS1_LDCXXFLAGS = -prof-gen
PASS2_LDCXXFLAGS = $(FASTNOSTATIC) -prof-use

400.perlbench=peak=default:
CC= icc -m64
CPORTABILITY= -DSPEC_CPU_LP64 -DSPEC_CPU_LINUX_X64
COPTIMIZE= -auto-ilp32

401.bzip2=peak=default:
CC= icc -m64
CPORTABILITY= -DSPEC_CPU_LP64
COPTIMIZE= -opt-prefetch  -auto-ilp32 -ansi-alias

403.gcc=peak=default:
COPTIMIZE = $(FASTNOSTATIC)
feedback=0

429.mcf=peak=default:
basepeak=yes

445.gobmk=peak=default:
PASS1_CFLAGS     = -prof-gen
PASS2_CFLAGS     = $(SSE) -prof-use
PASS1_LDCFLAGS   = -prof-gen
PASS2_LDCFLAGS   = $(SSE) -prof-use

456.hmmer=peak=default:
CC= icc -m64
CPORTABILITY= -DSPEC_CPU_LP64
COPTIMIZE=  $(FASTNOSTATIC) -unroll2  -auto-ilp32
feedback=no

458.sjeng=peak=default:
CC= icc -m64
CPORTABILITY= -DSPEC_CPU_LP64
COPTIMIZE= -unroll4 -auto-ilp32

462.libquantum=peak=default:
basepeak=yes

464.h264ref=peak=default:
COPTIMIZE=  -unroll2 -ansi-alias

471.omnetpp=peak=default:
CXXOPTIMIZE=  -ansi-alias -opt-ra-region-strategy=block

473.astar=peak=default:
basepeak=yes

483.xalancbmk=peak=default:
basepeak=yes

################################################################
# Peak Tuning Flags for FP
################################################################
fp=peak=default:
COPTIMIZE=       -auto-ilp32
CXXOPTIMIZE=     -auto-ilp32
PASS1_CFLAGS =   -prof-gen
PASS2_CFLAGS =   $(FASTNOSTATIC) -opt-mem-layout-trans=3 -prof-use
PASS1_CXXFLAGS = -prof-gen
PASS2_CXXFLAGS = $(FASTNOSTATIC) -opt-mem-layout-trans=3 -prof-use
PASS1_FFLAGS =   -prof-gen
PASS2_FFLAGS =   $(FASTNOSTATIC)                         -prof-use
PASS1_LDFLAGS =  -prof-gen
PASS2_LDFLAGS =  $(FASTNOSTATIC)                         -prof-use

410.bwaves=peak=default:
basepeak=yes
####################################################################################################################################
%ifdef %{smt}
copies=%{cores}
%ifdef %{physicallogical}
submit       = numactl --localalloc --physcpubind=`expr 2 \\* $SPECCOPYNUM` $command
%ifdef %{no-numa}
submit       = taskset -c `expr 2 \\* $SPECCOPYNUM` $command
%endif
%endif
%endif
####################################################################################################################################

416.gamess=peak=default:
OPTIMIZE= -unroll2 -inline-level=0  -scalar-rep-

433.milc=peak=default:
OPTIMIZE=

434.zeusmp=peak=default:
basepeak=yes
feedback=0

435.gromacs=peak=default:
OPTIMIZE= -opt-prefetch

436.cactusADM=peak=default:
basepeak=yes

437.leslie3d=peak=default:
OPTIMIZE=     $(FAST) -opt-prefetch
feedback=no
####################################################################################################################################
%ifdef %{smt}
copies=%{cores}
%ifdef %{physicallogical}
submit       = numactl --localalloc --physcpubind=`expr 2 \\* $SPECCOPYNUM` $command
%ifdef %{no-numa}
submit       = taskset -c `expr 2 \\* $SPECCOPYNUM` $command
%endif
%endif
%endif
####################################################################################################################################

444.namd=peak=default:
CXXOPTIMIZE= -fno-alias -auto-ilp32

447.dealII=peak=default:
basepeak=yes

450.soplex=peak=default:
PORTABILITY =
CXX= icpc -m32 -L/opt/intel/composer_xe_2015/lib/ia32
OPTIMIZE= -opt-malloc-options=3
CXXOPTIMIZE=
####################################################################################################################################
%ifdef %{smt}
copies=%{cores}
%ifdef %{physicallogical}
submit       = numactl --localalloc --physcpubind=`expr 2 \\* $SPECCOPYNUM` $command
%ifdef %{no-numa}
submit       = taskset -c `expr 2 \\* $SPECCOPYNUM` $command
%endif
%endif
%endif
####################################################################################################################################

453.povray=peak=default:
CXXOPTIMIZE= -unroll4  -ansi-alias

454.calculix=peak=default:
basepeak=yes

459.GemsFDTD=peak=default:
basepeak=yes
####################################################################################################################################
%ifdef %{smt}
copies=%{cores}
%ifdef %{physicallogical}
submit       = numactl --localalloc --physcpubind=`expr 2 \\* $SPECCOPYNUM` $command
%ifdef %{no-numa}
submit       = taskset -c `expr 2 \\* $SPECCOPYNUM` $command
%endif
%endif
%endif
####################################################################################################################################

465.tonto=peak=default:
OPTIMIZE= -unroll4 -auto -inline-calloc -opt-malloc-options=3

470.lbm=peak=default:
basepeak=yes

481.wrf=peak=default:
OPTIMIZE=     $(FAST)
feedback=0

482.sphinx3=peak=default:
OPTIMIZE= $(FASTNOSTATIC) -opt-mem-layout-trans=3
COPTIMIZE= -unroll2
feedback=no

#################################################################
# (Edit this to match your system)
#################################################################

default=default=default=default:

#include: SUT-rate.conf
#  ----- Begin inclusion of 'SUT-rate.conf'
############################################################################
default=default=default=default:
license_num      = 19
test_sponsor     = Fujitsu
hw_avail         = Apr-2015
sw_avail         = Sep-2014
tester           = Fujitsu
hw_memory        = 256 GB (16 x 16 GB 2Rx4 PC4-2133P-R)
hw_disk          = 1 x SATA, 500 GB, 7200 RPM
hw_fpu           = Integrated
hw_ncpuorder     = 1,2 chip
hw_vendor        = Fujitsu
sw_file          = xfs
hw_pcache        = 32 KB I + 32 KB D on chip per core
hw_scache        = 256 KB I+D on chip per core
hw_tcache        = 20 MB I+D on chip per chip
hw_ocache        = None
hw_other         = None
hw_nthreadspercore = 2
prepared_by      = Fujitsu
sw_os000         = Red Hat Enterprise Linux Server release 7.1
sw_os001 = (Maipo)
sw_os002         = Kernel 3.10.0-229.el7.x86_64
sw_state         = Run level 3 (multi-user)
notes_plat_000   = BIOS configuration:
notes_plat_005   = Energy Performance = Performance
notes_plat_010   = Utilization Profile = Unbalanced
notes_plat_015   = QPI snoop mode: Early Snoop
notes_plat_020   =     COD Enable = Disabled, Early Snoop = Enabled
notes_plat_025   = CPU C1E Support = Disabled
notes_055        =
notes_060        = This result was measured on the PRIMERGY RX2560 M1. The PRIMERGY RX2560 M1
notes_065        = and the PRIMERGY TX2560 M1 are electronically equivalent.
notes_070        = For information about Fujitsu please visit: http://www.fujitsu.com
hw_cpu_name      = Intel Xeon E5-2620 v3
hw_cpu_char      = Intel Turbo Boost Technology up to 3.20 GHz
hw_cpu_mhz       = 2400
hw_model         = PRIMERGY TX2560 M1, Intel Xeon E5-2620 v3, 2.4 GHz
hw_ncores        = 12
hw_nchips        = 2
hw_ncoresperchip = 6
hw_nthreadspercore = 2
hw_tcache        = 15 MB I+D on chip per chip
hw_memory000     = 256 GB (16 x 16 GB 2Rx4 PC4-2133P-R, running at
hw_memory001 = 1866 MHz)
# ---- End inclusion of '/home/SPECcpu2006/config/SUT-rate.conf'

notes_submit_000 = The numactl mechanism was used to bind copies to processors. The config file option 'submit'
notes_submit_005 = was used to generate numactl commands to bind each copy to a specific processor.
notes_submit_010 = For details, please see the config file.
%ifdef %{no-numa}
notes_submit_000 = The taskset mechanism was used to bind copies to processors. The config file option 'submit'
notes_submit_001 = was used to generate taskset commands to bind each copy to a specific processor.
notes_submit_002 = For details, please see the config file.
%endif
notes_015        = Binaries compiled on a system with 1x Core i5-4670K CPU + 16GB
notes_020        = memory using RedHat EL 7.0
notes_os_000     = Stack size set to unlimited using "ulimit -s unlimited"

int=default=default=default:
sw_compiler001   = C/C++: Version 15.0.0.090 of Intel C++ Studio XE
sw_compiler002   = for Linux
sw_base_ptrsize  = 32-bit
sw_peak_ptrsize  = 32/64-bit
sw_other001      = Microquill SmartHeap V10.0

default:
%ifdef %{THP_enabled}
notes_025        = Transparent Huge Pages enabled with:
notes_030        = echo always > /sys/kernel/mm/transparent_hugepage/enabled
%endif

%ifdef %{THP_disabled}
notes_200        = Transparent Huge Pages disabled with:
notes_201        = echo never  > /sys/kernel/mm/transparent_hugepage/enabled
%endif

%ifdef %{drop_caches}
notes_035        = Filesystem page cache cleared with:
notes_040        = echo 1>       /proc/sys/vm/drop_caches
%endif

%ifdef %{invoke_with_interleave}
notes_045        = runspec command invoked through numactl i.e.:
notes_050        = numactl --interleave=all runspec <etc>
%endif

fp=default=default=default:
sw_compiler000   = C/C++: Version 15.0.0.090 of Intel C++ Studio XE
sw_compiler001   = for Linux;
sw_compiler002   = Fortran: Version 15.0.0.090 of Intel Fortran
sw_compiler003   = Studio XE for Linux
sw_base_ptrsize  = 32/64-bit
sw_peak_ptrsize  = 32/64-bit
sw_other = None


# The following settings were obtained by running 'specperl $[top]/config/sysinfo.rev6914 -p -f'
default:
# Sysinfo program /home/SPECcpu2006/config/sysinfo.rev6914
# $Rev: 6914 $ $Date:: 2014-06-25 #$ e3fbb8667b5a285932ceab81e28219e1
# running on RX2560 M1 Tue Apr 14 11:12:55 2015
#
# This section contains SUT (System Under Test) info as seen by
# some common utilities.  To remove or add to this section, see:
#   http://www.spec.org/cpu2006/Docs/config.html#sysinfo
#
# From /proc/cpuinfo
#    model name : Intel(R) Xeon(R) CPU E5-2620 v3 @ 2.40GHz
#       2 "physical id"s (chips)
#       24 "processors"
#    cores, siblings (Caution: counting these is hw and system dependent.  The
#    following excerpts from /proc/cpuinfo might not be reliable.  Use with
#    caution.)
#       cpu cores : 6
#       siblings  : 12
#       physical 0: cores 0 1 2 3 4 5
#       physical 1: cores 0 1 2 3 4 5
#    cache size : 15360 KB
#
# From /proc/meminfo
#    MemTotal:       263839568 kB
#    HugePages_Total:       0
#    Hugepagesize:       2048 kB
#
# From /etc/*release* /etc/*version*
#    os-release:
#       NAME="Red Hat Enterprise Linux Server"
#       VERSION="7.1 (Maipo)"
#       ID="rhel"
#       ID_LIKE="fedora"
#       VERSION_ID="7.1"
#       PRETTY_NAME="Red Hat Enterprise Linux Server 7.1 (Maipo)"
#       ANSI_COLOR="0;31"
#       CPE_NAME="cpe:/o:redhat:enterprise_linux:7.1:GA:server"
#    redhat-release: Red Hat Enterprise Linux Server release 7.1 (Maipo)
#    system-release: Red Hat Enterprise Linux Server release 7.1 (Maipo)
#    system-release-cpe: cpe:/o:redhat:enterprise_linux:7.1:ga:server
#
# uname -a:
#    Linux RX2560 M1 3.10.0-229.el7.x86_64 #1 SMP Thu Jan 29 18:37:38 EST 2015
#    x86_64 x86_64 x86_64 GNU/Linux
#
# run-level 5 Apr 14 11:08
#
# SPEC is set to: /home/SPECcpu2006
#    Filesystem            Type  Size  Used Avail Use% Mounted on
#    /dev/mapper/rhel-home xfs   412G  3.5G  408G   1% /home
# Additional information from dmidecode:
#
#    Warning: Use caution when you interpret this section. The 'dmidecode' program
#    reads system data which is "intended to allow hardware to be accurately
#    determined", but the intent may not be met, as there are frequent changes to
#    hardware, firmware, and the "DMTF SMBIOS" standard.
#
#   BIOS FUJITSU // American Megatrends Inc. V5.0.0.9 R1.19.0.0_NextRelease for
#   D3289-A1x       03/18/2015
#   Memory:
#    8x Micron 36ASF2G72PZ-2G1A2 16 GB 2 rank 2133 MHz, configured at 1866 MHz
#    8x NO DIMM NO DIMM
#    1x Samsung M393A2G40DB0-CP 16 GB 2 rank 2133 MHz, configured at 1866 MHz
#    7x Samsung M393A2G40DB0-CPB 16 GB 2 rank 2133 MHz, configured at 1866 MHz
#
# (End of data from sysinfo program)
# hw_cpu_name    = Intel Xeon E5-2620 v3
# hw_disk        = 412 GB  add more disk info here
# hw_memory001   = 251.617 GB fixme: If using DDR3, format is:
# hw_memory002   = 'N GB (M x N GB nRxn PCn-nnnnnR-n, ECC)'
# hw_nchips      = 2
# prepared_by    = root  (is never output, only tags rawfile)
# sw_file        = xfs
# sw_os001       = Red Hat Enterprise Linux Server release 7.1 (Maipo)
# sw_os002       = 3.10.0-229.el7.x86_64
# sw_state       = Run level 5 (add definition here)


# The following section was added automatically, and contains settings that
# did not appear in the original configuration file, but were added to the
# raw file after the run.

433.milc:
# The following setting was inserted automatically as a result of
# post-run basepeak application.
basepeak = 1

default:
notes_000 =Environment variables set by runspec before the start of the run:
notes_005 =LD_LIBRARY_PATH = "/home/SPECcpu2006/libs/32:/home/SPECcpu2006/libs/64:/home/SPECcpu2006/sh"
notes_010 =