# Invocation command line:
# /cpu2006/bin/runspec -c SLES10x64_ic10.0_em64t_Jun042007 -T all --input ref -n 3 --rate 8 -o all int
# output_root was not used for this run
############################################################################
###############################################################
# SPEC CPU2006 v1.0 Intel SLES10 x64 (64-bit) config file     #
# Jun 04 2007 Intel Compiler 10.0 for Linux Intel EM64T       #
###############################################################

action      = validate
tune        = base or peak
ext         = SLES10x64_ic10.0_em64t_Jun042007
PATHSEP     = /
flagsurl000 = http://www.spec.org/cpu2006/flags/FSC_Intel_flags.xml

check_md5   = 1
mean_anyway = 1
reportable  = 1

#include: SUT.inc
#  ----- Begin inclusion of 'SUT.inc'
############################################################################
# File to be included into config file for SPEC CPU2006

# This include file specifies the "System Under Test" (Hardware,
# OS, BIOS, etc.)
# Any information about the binaries is elsewhere.

# To avoid conflicts in the numbering of the notes,
# please use only 900 and higher numbers.

#######################################################################
# System information                                                  #
# If some remarks about BIOS or Firmware are needed, place them here. #
####################################################################### 

default=default=default=default:
notes_000=
notes_020=
notes_025= BIOS configuration:
notes_030= Hardware Prefetch = Disable, Adjacent Sector Prefetch = Disable

int=default=default=default:
notes_005= All binaries were built with 32-bit Intel compiler except:
notes_010= 401.bzip2 and 456.hmmer in peak were built with 64-bit Intel
notes_015= compiler by changing the path for include and library files.

#fp=default=default=default:
#notes901= All binaries were built with 64-bit Intel compiler except:
#notes902= 433.milc, 434.zeusmp, 450.soplex, 470.lbm and 482.sphinx3 in peak were built with
#notes903= 32-bit Intel compiler by changing the path for include and library files.

###################################
# About Fujitsu Siemens Computers #
###################################

default=default=default=default:
notes_035=
notes_040= The PRIMERGY RX300 S3 and the PRIMERGY TX300 S3 are electronically equivalent.
notes_045=
notes_050 = For information about Fujitsu Siemens Computers please see:
notes_055 = http://www.fujitsu-siemens.com

#####################################
# Description Hardware and Software #
#####################################

default=default=default=default:
hw_vendor          = Fujitsu Siemens Computers
hw_model000        = PRIMERGY RX300 S3, Intel Xeon processor X5355,
hw_model001 = 2.66 GHz
hw_cpu_name        = Intel Xeon X5355
hw_cpu_char        = 1333 MHz system bus
hw_cpu_mhz         = 2667
hw_fpu             = Integrated
#
hw_nchips          = 2
hw_ncores          = 8
hw_ncoresperchip   = 4
hw_nthreadspercore = 1
#
hw_ncpuorder       = 1,2 chips
hw_pcache          = 32 KB I + 32 KB D on chip per core
hw_scache          = 8 MB I+D on chip per chip, 4 MB shared / 2 cores
hw_tcache          = None
hw_ocache          = None
hw_memory000       = 8 GB (8x1 GB DDR2 PC2-5300F, 2 rank, CAS 5-5-5,
hw_memory001 = with ECC)
hw_disk            = Seagate ST373454SS (SAS, 73GB, 15000rpm)
hw_other           = None

sw_file            = ext2
sw_state           = Multiuser, Runlevel 3

license_num        = 22
test_sponsor       = Fujitsu Siemens Computers
tester             = Fujitsu Siemens Computers
test_date          = Jun-2007
hw_avail           = Jan-2007
prepared_by        = Fujitsu Siemens Computers
config             = SLES10x64_ic10.0_em64t_Jun042007.cfg
# ---- End inclusion of '/cpu2006/config/SUT.inc'

default=default=default=default:
CC  = icc
CXX = icpc
FC  = ifort
OBJ = .o

SMARTHEAP_DIR = /opt/SmartHeap_8_1/lib

#submit= MYMASK=`printf '0x%x' \$((1<<\$SPECCOPYNUM))`; /usr/bin/taskset \$MYMASK $command

###########################
# portability & libraries #
###########################

400.perlbench=default=default=default:
CPORTABILITY = -DSPEC_CPU_LINUX_IA32

403.gcc=default=default=default:
EXTRA_CFLAGS = -Dalloca=_alloca

462.libquantum=default=default=default:
CPORTABILITY = -DSPEC_CPU_LINUX

483.xalancbmk=default=default=default:
CXXPORTABILITY = -DSPEC_CPU_LINUX

435.gromacs=default=default=default:
LDPORTABILITY = -nofor_main

436.cactusADM=default=default=default:
LDPORTABILITY = -nofor_main
PORTABILITY = -DSPEC_CPU_LP64

454.calculix=default=default=default:
LDPORTABILITY = -nofor_main

481.wrf=default=default=default:
CPORTABILITY = -DSPEC_CPU_CASE_FLAG -DSPEC_CPU_LINUX

#########################
# Baseline Tuning Flags #
#########################

int=base=default=default:
COPTIMIZE= -fast 
CXXOPTIMIZE= -xT -O3 -ipo -no-prec-div -ansi-alias
EXTRA_CXXLIBS= -L$(SMARTHEAP_DIR) -lsmartheap

fp=base=default=default:
OPTIMIZE= -fast

#####################
# Peak Tuning Flags #
#####################

int=peak=default=default:
COPTIMIZE= -fast 
CXXOPTIMIZE= -fast -ansi-alias 
EXTRA_CXXLIBS= -L$(SMARTHEAP_DIR) -lsmartheap

PASS1_CFLAGS   = -prof_gen
PASS2_CFLAGS   = -prof_use
PASS1_CXXFLAGS = -prof_gen
PASS2_CXXFLAGS = -prof_use
PASS1_LDFLAGS  = -prof_gen
PASS2_LDFLAGS  = -prof_use

fp=peak=default=default:
OPTIMIZE= -fast

PASS1_CFLAGS   = -prof_gen
PASS2_CFLAGS   = -prof_use
PASS1_FFLAGS   = -prof_gen
PASS2_FFLAGS   = -prof_use
PASS1_CXXFLAGS = -prof_gen
PASS2_CXXFLAGS = -prof_use
PASS1_LDFLAGS  = -prof_gen
PASS2_LDFLAGS  = -prof_use

401.bzip2=peak=default=default:
CC=/opt/intel/cce/10.0.023/bin/icc -I/opt/intel/cce/10.0.023/include -L/opt/intel/cce/10.0.023/lib
PORTABILITY=-DSPEC_CPU_LP64
feedback=0

403.gcc=peak=default=default:
basepeak=yes

429.mcf=peak=default=default:
COPTIMIZE= -fast -prefetch 
EXTRA_LIBS= -L$(SMARTHEAP_DIR) -lsmartheap

456.hmmer=peak=default=default:
COPTIMIZE= -fast -unroll2 
CC=/opt/intel/cce/10.0.023/bin/icc -I/opt/intel/cce/10.0.023/include -L/opt/intel/cce/10.0.023/lib
PORTABILITY=-DSPEC_CPU_LP64

458.sjeng=peak=default=default:
COPTIMIZE= -fast -unroll4 

462.libquantum=peak=default=default:
COPTIMIZE= -fast -prefetch -opt-streaming-stores always 

464.h264ref=peak=default=default:
OPTIMIZE= -fast -unroll2 -ansi-alias 

483.xalancbmk=peak=default=default:
basepeak=yes

#410.bwaves=peak=default=default:
#basepeak=yes

#416.gamess=peak=default=default:
#basepeak=yes

#433.milc=peak=default=default:
#PORTABILITY= 
#CC=/opt/intel/cc/9.1.047/bin/icc -I/opt/intel/cc/9.1.047/include -L/opt/intel/cc/9.1.047/lib

#434.zeusmp=peak=default=default:
#PORTABILITY= 
#FC=/opt/intel/fc/9.1.043/bin/ifort -I/opt/intel/fc/9.1.043/include -L/opt/intel/fc/9.1.043/lib
#feedback=0

#436.cactusADM=peak=default=default:
#basepeak=yes

#437.leslie3d=peak=default=default:
#basepeak=yes

#444.namd=peak=default=default:
#basepeak=yes

#450.soplex=peak=default=default:
#PORTABILITY= 
#CXX=/opt/intel/cc/9.1.047/bin/icpc -I/opt/intel/cc/9.1.047/include -L/opt/intel/cc/9.1.047/lib

#459.GemsFDTD=peak=default=default:
#basepeak=yes

#470.lbm=peak=default=default:
#PORTABILITY= 
#CC=/opt/intel/cc/9.1.047/bin/icc -I/opt/intel/cc/9.1.047/include -L/opt/intel/cc/9.1.047/lib

#481.wrf=peak=default=default:
#basepeak=yes

#482.sphinx3=peak=default=default:
#PORTABILITY= 
#CC=/opt/intel/cc/9.1.047/bin/icc -I/opt/intel/cc/9.1.047/include -L/opt/intel/cc/9.1.047/lib
#feedback=0

#########################
# Used Compilers and OS #
#########################

int=default=default=default:
sw_compiler000   = Intel C++ Compiler for IA32/EM64T application,
sw_compiler001   = Version 10.0 - Build 20070308, Package-ID:
sw_compiler002 = l_cc_p_10.0.023
sw_other000      = Smart Heap Library, Version 8.1
sw_other001      = binutils-2.17.tar.gz, Version 2.17
sw_base_ptrsize  = 32-bit
sw_peak_ptrsize  = 32/64-bit

fp=default=default=default:
sw_compiler001   = Intel C++ Compiler for IA32/EM64T application,
sw_compiler002   = Version 10.0 - Build 20070308, Package-ID: l_cc_p_10.0.017
sw_compiler003   = Intel Fortran Compiler for IA32/EM64T application,
sw_compiler004   = Version 10.0 - Build 20070308, Package-ID: l_fc_p_10.0.017
sw_other         = None
sw_base_ptrsize  = 64-bit
sw_peak_ptrsize  = 64-bit

default=default=default=default:
sw_os000         = SUSE LINUX Enterprise Server 10 (x86_64), Kernel
sw_os001 = 2.6.16.21-0.8-smp
sw_avail         = Jun-2007
sw_auto_parallel = No

######################
# End of config-file #
######################